For Sale: Lots of items for sale

[Jolly Roger]

I have just significantly reduced the prices on these items, because I want them out of my locker. I will also consider offers.

One 11 gallon Kuuma hot water tank, approximately 22” high x 18” deep x 16” wide, with engine and hot water take-offs on the front. This is presently in my boat and working fine. I want to replace it with a 20 gallon tank. $225.00

Sail with sliders: 28’ luff, 10’7” foot, 30’3” leech with approx 12” roach. Four batten pockets. 8oz Dacron in good clean condition. $125.00

18” diameter stainless steel sink. $20

Two 39’ 3½” long 1x19 stainless rigging wire with two 5/8” eyes. $40

Four 26’0” lengths of 5/16 1x19 rigging wire with 5/8” stud and 5/8” eye. $30 each

Stainless destroyer type wheel, 28” diameter, with 1” straight shaft, 1/4” keyway. (Defender’s price $482.00). $100

Two flexible PVC Dorade cowls and mounting rings, 3” diameter, Including brass mounting ring. $10 each

Outboard prop 12½” diam x 6 5/8” pitch. 3/4” straight spline. $30

Four through-hull deck drain pipes to outside of hull, Bronze fittings 1½” pipes. Cockpit drainage if you don’t like below waterline drains $10 each

4” diam cowl deck flange for a screw in cowl, with cover plate. Bronze $20

Four beautiful chrome rigging tangs. Right hand thread (top of turnbuckle), 5/8” thread and clevis hole. $30 each

Extended chrome rigging tang. 7” long with 3” x 5/8” right hand thread. 5/8” clevis. $40

Three bronze rigging tangs, 4” long x 5/8” right hand thread, 5/8” clevis,
$20 each

TV dish bracket, 1” thread. Polished stainless. $10.

Brand new over the top block. $20

3/8” thick stainless steel plate, 20” long x 9” wide for windlass mounting or something. $40

Various bits from Pro-Furl jib furler.


All items located in Orlando or Titusville, Florida. PayPall available.
See my website Items for sale to see pictures of everything.

[wsulli]

I will take the @ cowl vents advise shipping to 07446 thanks
will pay via paypal

[Jolly Roger]

will check it out tomorrow. JR

[Bluemansailor]

>>Various bits from Pro-Furl jib furler. << what bits do you have?

Looking for an upper stop and it's screw. Attaches to the upper part of the extrusions.

thanks Roland

[skipmac]

Might be interested in these.

Four through-hull deck drain pipes to outside of hull, Bronze fittings 1½” pipes. Cockpit drainage if you don’t like below waterline drains $10 each

But not certain I am clear on what they are. Are these thru hull fittings sometimes call mushrooms with threaded shaft and hose bard end or something similar?

Got a picture?


Thanks
Skip

[davido]

PM sent on 1x19 wire rope 39' 3.5" long

[eddi]

would buy upper swivel if diameter is 42mm inside
thanks

[Jolly Roger]

Originally Posted by Bluemansailor

>>Various bits from Pro-Furl jib furler. << what bits do you have?

Looking for an upper stop and it's screw. Attaches to the upper part of the extrusions.

thanks Roland

HI Roland,
Go to my website, all the Pro-Furl bits are shown at the bottom of the Items for sale page. JR

[Jolly Roger]

Originally Posted by skipmac

Might be interested in these.

Four through-hull deck drain pipes to outside of hull, Bronze fittings 1½” pipes. Cockpit drainage if you don’t like below waterline drains $10 each

But not certain I am clear on what they are. Are these thru hull fittings sometimes call mushrooms with threaded shaft and hose bard end or something similar?

Got a picture?
Thanks
Skip

Go to my website. All items are shown there. JR

[Jolly Roger]

Originally Posted by lesterbutch

Looking to sell a wind vane steering system off a 35' Pearson. Very good condition. This unit is heavy and would have to be trucked. I will consider all reasonable offers. The new price of this unit was around $2,000 25 years ago. Please contact me by email at:

wle0423@live.com

Unit is located in East Central Florida

Attention of Moderator.
Please remove this post from my thread. I don't appreciate somebody posting their own items on my message.

[Jolly Roger]

Originally Posted by eddi

would buy upper swivel if diameter is 42mm inside
thanks

I assume you mean the upper swivel for the Pro Furl? I will need to measure the inner dimension.
Sorry to all respondents, but we have just had a family emergency overseas, and I won't be back at my boat for a week at least.

[Jolly Roger]

The following items have been sold.
11 gallon water heater.
Two dorade cowls.
Stainless sink.

[Bluemansailor]

very Interested in the
Wrap stop. 9/32” bore but can be drilled for a bigger wire diameter.

when you get back to you boat, let me know how much - shipping to 19044

thanks, hope all is OK,
Roland